Electromagnetic Compatibility (EMC) requirements have been established in many
countries to regulate the radio frequency energy generated by Information Technology
Equipment (ITE). This energy is generated during the normal and intended use
of this equipment and so is limited by country regulations to levels intended
to minimize potential interference to other electrical equipment, including
public safety services.
Two levels of radio frequency energy are allowed according to the type or use
of equipment. Class A levels have been established for use in commercial or
business environments. Class B levels are lower than the Class A requirements
and have been established for use in residential environments. Class B levels
are also suitable when the environment includes electrically sensitive equipment.
The device you have purchased has been provided with a compliance label to
indicate where it may be used with reasonable protection to the environment
in which it is used. Additional statements are provided below as required by
the requirements of international and domestic regulations.
NOTE: Check the label on your product to determine the level of operation
Radio Frequency Interference Statement (Federal Communications Commission):
External Tape Drives Only
For Class B Devices
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Only the double-shielded data cable supplied by the
manufacturer should be used with external tape drives. Other types of
cables could void the manufacturer's warranty and violate FCC rules and
regulations.
NOTE: If the device is changed or modified without permission from
Dell, the user may void his or her authority to operate the equipment.
Notice for Canada (Industry Canada)
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the radio interference regulations of the
Canadian Department of Communications.
Le pr�sent appareil num�rique n'�met pas de bruits radio�lectriques d�passant
les limites applicables aux appareils num�riques de Class B prescrites dans
la règlement sur le brouillage radio�lectrique �dictè par le Ministère
des Communications du Canada.
CSA Information Statement (Internal Tape Drives Only)
INSTRUCTION TO USER:
WARNING: This component is only considered to be approved when
installed in CSA certified equipment evaluated to the standards C22.2 No.
220-M1986 or C22.2 No 950-1995. The operator accessibility into the end
use enclosure is defined with strict accordance in the operator's manual
for the installation of components into the equipment.
INSTRUCTIONS AUX UTILISATEURS:
AVERTISSEMENT: Ce composant n'est considéré agréé
que s'il est installé dans un equipement certifié CSA selon
les normes C22.2 No. 220-M1986 ou C22.2 No 950-1995. L'accessibilité
de l'opérateur a l'enceinte est définie en stricte conformité
avec le manuel l'opérateur pour l'installation de composants dans
l'équipements.
TUV (Internal Tape Drives Only)
This equipment must be supplied by a Safety-Extra-Low-Voltage (secondary circuit
in accordance with IEC 60950: 1991 up to and including A4: 1996). During incorporation
of the equipment, all requirements of IEC 60950: 1991 up to and including A4:
1996 must be observed and obeyed.
Regulatory Notices - General
LED Emission Level
This equipment has been tested and found to comply with the limits for a Class
1 LED product, set out in the international standard for safety of laser products.
Notice for the European Union
General Approval NS/G/1234/J/100003
This DELL PowerVault 110T LTO tape drive meets the General Approval NS/G/1234/J/100003
requirements.
This Product was tested in a typical configuration with Hewlett-Packard
server and peripherals.
The DELL PowerVault 110T LTO products were tested when installed within a
Hewlett-Packard LC series Netserver
The product herewith complies with the requirements of the
- Low Voltage Directive 73/23/EEC
- EMC Directive 89/336/EEC and carries the CE marking accordingly
The product complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
- This device may not cause harmful interference, and
-This device must accept any interference received, including interference
that may cause undesired operation.
