User Guide

User Guide
Display Assembly and Display Latch: Dell Inspiron XPS and Inspiron 9100 Service Manual

Back to Contents Page

Display Assembly and Display Latch

Dell™ Inspiron™ XPS and Inspiron 9100 Service Manual

  Display Bezel

  Display Panel

  Display Latch


CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.
  1. Follow the instructions in "Preparing to Work Inside the Computer."

NOTICE: Before turning the computer over and removing the screws, ensure that the display is firmly latched closed.
  1. Turn the computer over and remove the four screws (two on each side) labeled "D" on the bottom of the computer.

1

M2.5 x 6-mm screws labeled "D" (4)

  1. Turn the computer over and open the display.

  2. Remove the left, right, and center hinge covers.

  3. Disconnect the antenna cables (pull to separate the connectors).

1

display cable

2

antenna cables (2)

3

system board connector

  1. Use the pull-tab to disconnect the display cable.

  2. Lift the display out of the computer at a 90-degree angle.

1

display

Display

1

M2.5 x 6-mm screws (6)

5

display bezel

2

rubber display bumpers (6)

6

display panel

3

M2.5 x 6-mm shoulder screws (2)

7

display base

4

screw covers (2)

8

M2.5 x 3-mm screws (8)


Display Bezel

CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.
  1. Follow the instructions in "Preparing to Work Inside the Computer."

  2. Remove the display.

  3. Remove the six rubber display bumpers and two screw covers.

  4. Remove the six M2.5 x 6-mm screws and two M2.5 x 6-mm shoulder screws and remove the display bezel.

1

M2.5 x 6-mm screws (6)

2

rubber display bumpers (6)

3

display bezel

4

M2.5 x 6-mm shoulder screws (2)

5

screw covers (2)


Display Panel

CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.
  1. Follow the instructions in "Preparing to Work Inside the Computer."

  2. Remove the display.

  3. Remove the display bezel.

  4. Remove the M2 x 3-mm ground screw that attaches the display-panel ground wire to the back display cover.

  5. Remove the eight M2 x 3-mm screws from each side of the display panel.

  6. Lift the display panel out of the display cover.

1

display-panel ground wire

2

M2 x 3-mm ground screw

3

M2 x 3-mm screws (8)

4

display panel

  1. Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector.

  2. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector.

1

pull-tab on bottom flex-cable connector

2

top flex-cable connector

3

display connector

4

inverter connector


Display Latch

CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.
  1. Follow the instructions in "Preparing to Work Inside the Computer."

  2. Remove the display.

  3. Remove the display bezel.

  4. Remove the two M2.5 x 4-mm screws and remove the display latch.

1

M2.5 x 4-mm screws (2)

2

display latch


Back to Contents Page

 

Laptops | Desktops | Business Laptops | Business Desktops | Workstations | Servers | Storage | Monitors | Printers | Electronics
All rights reserved : About Dell | Site Terms | Terms and Conditions | Unresolved Issues | Privacy | Site Map | Feedback

* IMPORTANT DELL DETAILS:

Some Genuine Windows Vista® features - like the new Aero user interface - are only available in premium editions of Genuine Windows Vista® and require advanced or additional hardware (e.g. monitors). Check www.dell.com.my/vista for details.

**Dell's Terms and Conditions: apply to all sales available on request or at "Terms and Conditions of Sale" located at the bottom of our homepage at: www.dell.com.my

Prices and specifications are correct at date of publication but subject to availability or change without notice. Promotional deals apply to maximum order size of 3 desktop or laptop systems. Dell cannot guarantee that promotions and prices listed online will be available to purchase by telephone.

RETURNS POLICY: Dell’s “Returns Policy” found at http://www.dell.com.my applies to all sales. Choose carefully, as order cancellation rights are limited and additional costs may apply.

MISTAKES: While all efforts are made to check pricing and other errors, inadvertent errors do occur from time to time and Dell reserves the right to decline orders arising from such errors.

ONSITE SERVICE : Technician, replacement part or unit (depending on service contract) will be dispatched if necessary following phone-based troubleshooting. Subject to parts availability, geographical restrictions (on site and/or next business day service not available in some locations) and terms of service contract. Service timing dependent upon time of day call placed to Dell. Defective unit must be returned or paid for. Replacements may be refurbished .

COMPLETECOVER: service is available for personal computers, Axim PDAs, Dell branded projectors and LCD TV. CompleteCover excludes theft, loss, and damage due to fire, intentional damage, acts of God or natural disasters, animals, pets or pests. Customer may be required to return unit to Dell. For complete details refer to CompleteCover service agreement found at www.dell.com/ap/services . This service is only available in selected countries.

TRADEMARKS: Celeron, Celeron Inside, Core Inside, Intel, Intel Logo, Intel Atom, Intel Atom Inside, Intel Core, Intel Inside, Intel Inside Logo, Intel vPro, Itanium, Itanium Inside, Pentium, Pentium Inside, vPro Inside, Xeon, and Xeon Inside are trademarks of Intel Corporation in the U.S. and other countries.

COPYRIGHT: © 2011 Dell Inc. All rights reserved.

snWEB4