CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the System Information Guide.
You can increase your computer memory by installing memory modules on the system board. For information on the type of memory supported by your computer, look under "Memory" in "Specifications."
Before you install new memory modules, download the most recent BIOS for your computer from the Dell Support website at support.dell.com.
NOTICE: You can only place a CRIMM in memory module connectors 3 and
4. To locate the connectors, see "System Board Components."
Each memory socket on the system board must be occupied by either a RIMM or a CRIMM.
Memory Modules
1
RIMM
2
CRIMM
NOTICE: If you remove your original memory modules from the computer
during a memory upgrade, keep them separate from any new modules that you
may have, even if you purchased the new modules from Dell. You must install
your original memory modules in pairs either in connectors RIMM1 and
RIMM 2 or RIMM 3 and RIMM4. Do not pair one original memory module
with one new memory module. Otherwise, your computer may not start
properly.
Memory sockets must be upgraded in matched pairs. In other words, two sockets in a pair must contain modules of identical capacity with the same number of components and the same speed. To locate the memory sockets on the system board, see "System Board Components."
Memory Module Label
Mixed pairs of ECC and non-ECC modules all function as non-ECC.
Mixed pairs of PC1066 and PC800 modules all function as PC800.
Be sure to install a RIMM in socket 1 first (closest to the processor) before installing modules in the other sockets.
Ensure that your computer and attached devices are turned off. If your
computer and attached devices did not automatically turn off when
you shut down your computer, turn them off now.
NOTICE: To disconnect a network cable, first unplug the cable from your
computer and then unplug it from the network wall jack.
Disconnect any telephone or telecommunication lines from the
computer.
Disconnect your computer and all attached devices from electrical
outlets, and then press the power button to ground the system board.
If you have installed a padlock through the padlock ring on the back
panel, remove the padlock.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.
NOTICE: Before touching anything inside your computer, ground yourself by
touching an unpainted metal surface, such as the metal at the back of the
computer. While you work, periodically touch an unpainted metal surface to
dissipate any static electricity that could harm internal components.
Press out the securing clip at each end of the memory module
connector.
1
cutouts (2)
2
connector
3
memory module
4
notch
5
securing clips (2)
Align the notch on the bottom of the module with the crossbar in the
connector.
NOTICE: To avoid damage to the memory module, press the module straight
down into the socket with equal force applied at each end of the module.
Insert the module straight down into the connector, ensuring that it
fits into the vertical guides at each end of the connector. Press firmly
on the ends of the module until it snaps into place.
If you insert the module correctly, the securing clips snap into the cutouts at each end of the module.
NOTICE: To connect a network cable, first plug the cable into the network
wall jack and then plug it into the computer.
Connect your computer and devices to electrical outlets, and turn
them on.
Press <F2> to enter system setup and check the value for System
Memory.
The computer should have changed the value of System Memory to reflect the newly installed memory. Verify the new total. If it is correct, skip to step 8.
If the memory total is incorrect, turn off and disconnect your
computer and devices from electrical outlets. Open the computer
cover and check the installed memory modules to ensure that they are
seated properly in their sockets. Then repeat steps 4, 5, and 6.
When the System Memory total is correct, press <Esc> to exit system
setup.
Run the Dell Diagnostics to verify that the memory modules are
operating properly.
TRADEMARKS: Celeron, Celeron Inside, Core Inside, Intel, Intel Logo, Intel Atom, Intel Atom Inside, Intel Core, Intel Inside, Intel Inside Logo, Intel Viiv, Intel vPro, Itanium, Itanium Inside, Pentium, Pentium Inside, Viiv Inside, vPro Inside, Xeon, and Xeon Inside are trademarks of Intel Corporation in the U.S. and other countries. For more information about the Intel processor feature rating, please refer to www.intel.com/go/rating
RETURNS POLICY: Dell’s “Returns Policy” found at http://www.dell.co.in applies to all sales. Choose carefully, as order cancellation rights are limited and additional costs may apply.
MISTAKES: While all efforts are made to check pricing and other errors, inadvertent errors do occur from time to time and Dell reserves the right to decline orders arising from such errors.
Inclusive of delivery charges. The price excludes VAT (5%) and local taxes which vary basis jurisdiction.
