User Guide

User Guide
Replacing Lights: Dell XPS 625 Service Manual

Back to Contents Page

Replacing Lights

Dell™ XPS™ 625 Service Manual

  Replacing the Front LED Board

  Replacing the Rear LED Board


WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

Replacing the Front LED Board

NOTE: The front LED board is embedded on the front panel. To replace the front LED board, you must replace the front panel.
  1. Follow the procedures in Before You Begin.

  2. Remove the computer cover (see Replacing the Computer Cover).

  3. Remove the drive panel (see Replacing the Drive Panel).

  4. Release the four tabs that secure the front panel to the chassis.

  5. Carefully, pivot the front panel away from the computer to release it from the chassis.

1

FRONT_LED cable

2

tabs (4)

3

front panel

 

 

  1. Disconnect the FRONT_LED cable from the front panel to remove the front panel along with the front panel light board.

  2. To replace the front LED board, align the securing tabs on the front panel with the corresponding slots on the chassis; connect the FRONT_LED cable to the front panel.

1

front panel

2

FRONT_LED cable

3

securing tabs (4)

 

 

  1. Rotate the front panel towards the computer until it snaps into place.

  2. Replace the drive panel (see Replacing the Drive Panel).

  3. Replace the computer cover (see Replacing the Computer Cover).

  4. Connect your computer and devices to electrical outlets, and then turn them on.


Replacing the Rear LED Board

  1. Follow the procedures in Before You Begin.

  2. Remove the computer cover (see Replacing the Computer Cover).

  3. Remove the system board (see Replacing the System Board).

  4. Disconnect the REAR_LED_SENSOR cable from the master I/O board (see Master I/O Board Components).

  5. Gently push the release tab away from the chassis to release the rear LED board and then slide it up and away from the computer.

1

release tab

2

rear LED board

  1. To replace the rear LED board, connect the REAR_LED_SENSOR cable to the master I/O board (see Master I/O Board Components).

  2. Route the REAR_LED_SENSOR cable under the system board and replace the system board (see Replacing the System Board).

  3. Align the rear LED board with the metal tab on the chassis; then slide the rear LED board into place.

  4. Replace the system board (see Replacing the System Board).

  5. Replace the computer cover (see Replacing the Computer Cover).

  6. Connect your computer and devices to electrical outlets, and then turn them on.


Back to Contents Page

 

Laptops | Desktops | Business Laptops | Business Desktops | Workstations | Servers | Storage | Monitors
All rights reserved : About Dell | Site Terms | Terms and Conditions | Service Agreements | Unresolved Issues | Privacy | Site Map | Dell Recycling | Feedback

*IMPORTANT DELL DETAIL

TRADEMARKS: Celeron, Celeron Inside, Core Inside, Intel, Intel Logo, Intel Atom, Intel Atom Inside, Intel Core, Intel Inside, Intel Inside Logo, Intel Viiv, Intel vPro, Itanium, Itanium Inside, Pentium, Pentium Inside, Viiv Inside, vPro Inside, Xeon, and Xeon Inside are trademarks of Intel Corporation in the U.S. and other countries. For more information about the Intel processor feature rating, please refer to www.intel.com/go/rating

RETURNS POLICY: Dell’s “Returns Policy” found at http://www.dell.co.in applies to all sales. Choose carefully, as order cancellation rights are limited and additional costs may apply.

MISTAKES: While all efforts are made to check pricing and other errors, inadvertent errors do occur from time to time and Dell reserves the right to decline orders arising from such errors.

# The Easy EMI offer is valid only on Direct purchases from Dell. Processing fees of Rs. 999 and service taxes applicable.

Inclusive of delivery charges. The price excludes VAT (5%) and local taxes which vary basis jurisdiction.

snWEB3