CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
You can increase your computer memory by installing memory modules on the system board. See "Specifications" in your Owner's Manual for information on the memory supported by your computer. Install only memory modules that are intended for your computer.
NOTE: Memory modules purchased from Dell are covered under your computer warranty.
Your computer has two user-accessible SODIMM sockets that can be accessed from the bottom of the computer.
NOTICE: If you need to install memory modules in two connectors, install a memory module in the connector labeled "DIMM1" before you install a module in the connector labeled "DIMM2."
Removing the DIMM 1 Memory Module
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
NOTICE: If a memory module is installed in the DIMM 2 connector, remove it prior to removing the memory module from the DIMM 1 connector. Failure to do so could result in damaging both memory modules.
Turn the computer over and loosen the three captive screws along with the
M2.5 x 5-mm screw. Remove the module cover.
1
M2.5 x 5-mm screw
2
captive screws (3)
3
module cover
NOTICE: To prevent damage to the memory module connector, do not use tools to spread the memory module securing clips.
Use your fingertips to carefully spread apart the securing clips on each end
of the memory module connector until the module pops up.
Remove the module from the connector.
1
upper memory module connector
2
securing clips (2)
3
memory module (DIMM 1)
Replacing the DIMM 1 Memory Module
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Align the notch in the module edge connector with the tab in the
connector slot.
Slide the module firmly into the slot at a 45-degree angle, and rotate the
module down until it clicks into place. If you do not feel the click, remove
the module and reinstall it.
NOTE: If the memory module is not installed properly, the computer may not boot. No error message indicates this failure.
1
tab
2
notch
Replace the module cover.
Insert the battery into the battery bay, or connect the AC adapter to your
computer and an electrical outlet.
Turn on the computer.
As the computer boots, it detects the additional memory and automatically updates the system configuration information.
To confirm the amount of memory installed in the computer, click Start ® Help and Support® Dell System Information.
Removing the DIMM 2 Memory Module
The DIMM 2 memory module is located directly above the DIMM 1 memory module located on the bottom of the computer.
Turn the computer over and loosen the three captive screws along with the
M2.5 x 5-mm screw. Remove the module cover.
1
M2.5 x 5-mm screw
2
captive screws (3)
NOTICE: To prevent damage to the memory module connector, do not use tools to spread the memory module securing clips.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Use your fingertips to carefully spread apart the securing clips on each end
of the memory module connector until the module pops up.
Remove the module from the connector.
1
lower memory module connector
2
securing clips (2)
3
memory module (DIMM 2)
Replacing the DIMM 2 Memory Module
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Align the notch in the module edge connector with the tab in the
connector slot.
Slide the module firmly into the slot at a 45-degree angle, and rotate the
module down until it clicks into place. If you do not feel the click, remove
the module and reinstall it.
NOTE: If the memory module is not installed properly, the computer may not boot. No error message indicates this failure.
1
tab
2
notch
NOTICE: If the cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer.
Replace the module cover.
Insert the battery into the battery bay, or connect the AC adapter to your
computer and an electrical outlet.
Turn on the computer.
As the computer boots, it detects the additional memory and automatically updates the system configuration information.
To confirm the amount of memory installed in the computer, click Start ® Help and Support® Dell System Information.
Some Genuine Windows Vista® features - like the new Aero user interface - are only available in premium editions of Genuine Windows Vista® and require advanced or additional hardware (e.g. monitors). Check www.dell.com.my/vista for details.
**Dell's Terms and Conditions: apply to all sales available on request or at "Terms and Conditions of Sale" located at the bottom of our homepage at: www.dell.com.my
Prices and specifications are correct at date of publication but subject to availability or change without notice. Promotional deals apply to maximum order size of 3 desktop or laptop systems. Dell cannot guarantee that promotions and prices listed online will be available to purchase by telephone.
RETURNS POLICY: Dell’s “Returns Policy” found at http://www.dell.com.my applies to all sales. Choose carefully, as order cancellation rights are limited and additional costs may apply.
MISTAKES: While all efforts are made to check pricing and other errors, inadvertent errors do occur from time to time and Dell reserves the right to decline orders arising from such errors.
ONSITE SERVICE : Technician, replacement part or unit (depending on service contract) will be dispatched if necessary following phone-based troubleshooting. Subject to parts availability, geographical restrictions (on site and/or next business day service not available in some locations) and terms of service contract. Service timing dependent upon time of day call placed to Dell. Defective unit must be returned or paid for. Replacements may be refurbished .
COMPLETECOVER: service is available for personal computers, Axim PDAs, Dell branded projectors and LCD TV. CompleteCover excludes theft, loss, and damage due to fire, intentional damage, acts of God or natural disasters, animals, pets or pests. Customer may be required to return unit to Dell. For complete details refer to CompleteCover service agreement found at www.dell.com/ap/services . This service is only available in selected countries.
TRADEMARKS: Celeron, Celeron Inside, Core Inside, Intel, Intel Logo, Intel Atom, Intel Atom Inside, Intel Core, Intel Inside, Intel Inside Logo, Intel vPro, Itanium, Itanium Inside, Pentium, Pentium Inside, vPro Inside, Xeon, and Xeon Inside are trademarks of Intel Corporation in the U.S. and other countries.
