Back to Contents Page

Display Assembly

Dell™ XPS™ M1530 Service Manual

  Removing the Display Assembly

  Replacing the Display Assembly

  Removing the Display Bezel

  Replacing the Display Bezel

  Removing the Display Panel

  Replacing the Display Panel

  Removing the Display Panel Cable

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).

NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer.

Removing the Display Assembly

1. Follow the instructions in Before You Begin.
   
   
2. Remove the Hinge Covers and the Center Control Cover (see Removing the Hinge Covers and Center Control Cover).
   
   
3. Turn the computer upside down and loosen the four captive screws along with the M2.5 x 5-mm screw. Remove the memory module cover.
   
   

1	M2.5 x 5-mm screw	2	memory module cover
3	captive screw (4)

4. Remove the Mini Card cables from the Mini Cards if applicable (see Wireless Mini Cards).
   
   
5. Make note of the cable routing and carefully dislodge the Mini-Card antenna cables from their routing guides.
   
   

6. Remove the two M2.5 x 5-mm screws labeled "D" from the computer base.
   
   

7. Remove the keyboard (see Removing the Keyboard).
   
   
8. Remove the two M2.5 x 8-mm screws from each side of the display assembly.
   
   

9. Make note of the cable routing and carefully dislodge the Mini-Card antenna cables from their routing guides and pull the cables with their connectors through the system board so that they are clear of the computer base.
   
   

10. Pull on the display cable pull-tab to disconnect the display cable from the display connector on the system board.
    
    
11. Remove the camera cable connector from the system board.
    
    

1	display cable pull-tab	2	camera cable connector
3	pull the Mini-Card antenna cables out of the computer base through here

12. Remove the display assembly from the computer base.
    
    

Replacing the Display Assembly

1. Replace the camera cable.
   
   
2. Reconnect the display cable to the connector on the system board.
   
   
3. Make note of the cable routing and carefully slide the Mini-Card antenna cables through the system board and into their routing guides.
   
   
4. Replace the two M2.5 x 8-mm screws on each side of the display assembly.
   
   
5. Replace the keyboard (see Replacing the Keyboard).
   
   
6. Turn the computer over and replace the two M2.5 x 5-mm screws labeled "D" on the computer base.
   
   
7. Make note of the cable routing and carefully insert the Mini-Card antenna cables through their routing guides.
   
   
8. Reconnect the mini card cables to the Mini Cards if applicable (see Wireless Mini Cards).
   
   
9. Replace the hinge covers and center control cover (see Replacing the Hinge Covers and Center Control Cover).
   
   

Removing the Display Bezel

NOTICE: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel.

1. Remove the display assembly (see Removing the Display Assembly).
   
   
2. Using your fingertips, carefully pry up the inside edge of the display bezel.
   
   
3. Remove the display bezel.
   
   

1	display bezel

Replacing the Display Bezel

Realign the display bezel over the display panel, and gently snap into place.

Removing the Display Panel

1. Remove the display assembly (see Removing the Display Assembly).
   
   
2. Remove the display bezel (see Removing the Display Bezel).
   
   
3. Remove the six screws securing the display panel brackets.
   
   

1

display panel

2

screw (6)

4. Remove the display panel.
   
   
5. Remove the eight screws (four on each side) that secure the display panel brackets to the display panel.
   
   

1

display panel bracket (1 left, 1 right)

2

screw (8 total; 4 on each side)

Replacing the Display Panel

1. Attach the display bracket to the display panel by replacing the four screws on each side of the display panel.
   
   
2. Align the display panel with the display back and replace the six screws.
   
   
3. Replace the display bezel (see Replacing the Display Bezel).
   
   
4. Replace the display assembly (see Replacing the Display Assembly).
   
   

Removing the Display Panel Cable

1. Remove the display assembly (see Removing the Display Assembly).
   
   
2. Remove the display bezel (see Removing the Display Bezel).
   
   
3. Remove the display panel (see Removing the Display Panel).
   
   
4. Turn over the display panel, placing it on a clean surface.
   
   

NOTICE: To avoid damage to the computer when replacing the bottom flex cable, gently support the bottom of the inverter board with one finger as you reseat the bottom flex-cable connector. Do not bend the inverter board.

1	pull-tab of the bottom flex-cable connector	2	back of display panel
3	flex-cable	4	tape securing the top flex-cable connector

5. Gently pull the pull-tab on the bottom flex-cable connector to release the cable from the inverter board.
   
   
6. Lift the tape that secures the top flex-cable connector and disconnect the connector.
   
   

Back to Contents Page